Skip to content
thecalculatorstudio

Ohm's Law Calculator: Voltage, Current, Resistance and Power

Choose the two quantities you know and enter them. You get the other two, with the formulas used, and the results shown with milli and kilo prefixes where they help.

Last reviewed

V
A

Resistance and power

6 Ω · 24 W

R = V ÷ I, P = V × I

Voltage
12 V
Current
2 A
Resistance
6 Ω
Power
24 W

For a resistor, V = I × R and P = V × I. The calculator uses SI units: volts, amperes, ohms and watts. Type 0.02 for 20 milliamperes and 4700 for 4.7 kilohms.

The two laws

Ohm’s law says that the current through most materials is directly proportional to the voltage applied across them. OpenStax’s College Physics writes it as I = V ÷ R, or equivalently V = I × R. The constant R is the resistance, measured in ohms (Ω), where 1 Ω = 1 V/A.

The power law gives the rate at which energy is turned into heat in a resistor, in watts: P = V × I. Substituting Ohm’s law gives two more forms:

  • P = I² × R
  • P = V² ÷ R

These four quantities, voltage V, current I, resistance R and power P, are linked by six pairs of formulas. Know any two and you can find the other two.

The formulas by what you know

You know Resistance R Power P Current I Voltage V
V and I V ÷ I V × I
V and R V² ÷ R V ÷ R
V and P V² ÷ P P ÷ V
I and R I² × R I × R
I and P P ÷ I² P ÷ I
R and P √(P ÷ R) √(P × R)

Worked examples

  • The OpenStax headlight. 12.0 V and 2.50 A: R = 12.0 ÷ 2.50 = 4.8 Ω and P = 12 × 2.5 = 30 W.
  • A kettle element. 230 V across 46 Ω: I = 230 ÷ 46 = 5 A and P = 230² ÷ 46 = 1,150 W.
  • A resistor. 0.5 A through 100 Ω: V = 0.5 × 100 = 50 V and P = 0.5² × 100 = 25 W.
  • A bulb. 60 W at 120 V: I = 60 ÷ 120 = 0.5 A and R = 120² ÷ 60 = 240 Ω.
  • A heater. 100 W in 25 Ω: I = √(100 ÷ 25) = 2 A and V = √(100 × 25) = 50 V.

Reading the results

Results show SI prefixes where they make a number easier to read: milli (m) for a thousandth, kilo (k) for a thousand and mega (M) for a million. So 0.02 A is shown as 20 mA, and 4,700 Ω as 4.7 kΩ. You enter values in the plain units: volts, amperes, ohms and watts.

Where it stops being true

Ohm’s law describes ohmic devices, where the resistance is steady. A resistor at a steady temperature behaves this way. A diode does not, because its current rises sharply with voltage. A lamp’s filament does not either: its resistance rises as it heats. OpenStax notes that a headlight’s cold resistance is lower than its running resistance, so it draws more current when first switched on. The calculator uses the running values you give it.

Common mistakes

  • Mixing units. Milliamperes and kilohms must be converted: 5 mA is 0.005 A.
  • Using the wrong formula for power. P = V × I always works, P = I² × R and P = V² ÷ R only for resistors.
  • Forgetting that AC needs more. In AC circuits with reactance, the power also depends on the power factor.
  • Treating a rating as a measurement. A bulb marked 60 W draws that power at its rated voltage only.

Colour-coded resistors are decoded with the resistor colour code calculator. For the current from power and voltage in AC circuits, use the watts to amps calculator, and for the loss in a cable the voltage drop calculator.

Two resistors in series

A 1 kΩ and a 2 kΩ resistor in series on a 9 V supply have a total resistance of 3 kΩ, so the current is 9 ÷ 3,000 = 3 mA through both. The voltage across the 1 kΩ resistor is 0.003 × 1,000 = 3 V, and across the 2 kΩ resistor it is 6 V. The two add back to 9 V. The power is 9 × 0.003 = 0.027 W, with 0.009 W in the first and 0.018 W in the second.

Checking a power rating

A 100 Ω resistor across 12 V dissipates 12² ÷ 100 = 1.44 W. A small quarter-watt resistor would be far over its limit, so choose one rated well above the figure you calculate.

How it is calculated

All formulas use exact decimal arithmetic to 50 digits, with square roots taken in the same arithmetic, and results are shown to 12 significant figures.

Frequently asked questions

What is Ohm's law?

The current through most materials is proportional to the voltage across them: V = I × R, or I = V ÷ R. The constant of proportionality is the resistance, measured in ohms, where one ohm is one volt per ampere.

What is the power formula?

The power in watts is voltage times current: P = V × I. Combined with Ohm's law this gives P = I² × R and P = V² ÷ R. A 12 V supply driving 2.5 A delivers 30 W.

How do I find the resistance from the voltage and current?

Divide: R = V ÷ I. OpenStax's example is a car headlight carrying 2.50 A from 12.0 V, which has a resistance of 12.0 ÷ 2.50 = 4.80 Ω.

How do I find the current from power and voltage?

Divide: I = P ÷ V. A 60 W bulb on 120 V draws 0.5 A, and its resistance is V² ÷ P = 14,400 ÷ 60 = 240 Ω.

Does Ohm's law always hold?

Not for every device. It describes materials where the current is proportional to the voltage, such as most resistors and metal wires. A diode or a lamp filament does not follow it exactly, because its resistance changes with the voltage or the temperature.

What units should I enter?

Volts, amperes, ohms and watts. Convert first: 20 milliamperes is 0.02 A and 4.7 kilohms is 4700 Ω. The results are shown with prefixes such as mA and kΩ for readability.

Related calculators

Sources