Skip to content
thecalculatorstudio

Amps to Watts Calculator (DC, AC and Three-Phase)

Enter the current and the voltage. Choose DC, single-phase or three-phase AC, and for AC the power factor, to get watts and volt-amperes.

Last reviewed

amps
volts

Power

1,200 W

1.2 kW · apparent power 1,200 VA

Formula
W = A × V × PF
Power in kilowatts
1.2 kW

This is arithmetic from the numbers you enter. Check the rating plate and ask a qualified electrician about wiring, fuses and breakers. This page is information, not electrical advice.

The formulas

Power in watts comes from current in amps and voltage in volts. Which formula to use depends on the supply:

Supply Watts
DC, or a simple resistive heater or bulb W = A × V
AC, single phase W = A × V × PF
AC, three phase (balanced load) W = √3 × A × V × PF

Here A is the current in amps, V is the voltage and PF is the power factor. For three-phase supplies V is the voltage between two lines and A is the current in each line. The power factor is a number between 0 and 1 that describes how much of the apparent power does useful work. It is 1 for a plain heater or incandescent bulb, and lower for motors and other loads that store energy.

OpenStax’s physics texts give the basic law, P = IV, and for an alternating current the average power P = I(rms) × V(rms) × cos φ, where cos φ is the power factor. The three-phase form follows from it. In a symmetrical star-connected system the line-to-line voltage is √3 times the voltage across each phase, and three phases each carry the same power, so the total is 3 × (V ÷ √3) × A × PF = √3 × V × A × PF.

Volt-amperes and watts

Multiply the current by the voltage and you get the apparent power in volt-amperes (VA). Multiply that by the power factor and you get the real power in watts. For a power factor of 1 they are the same. The calculator shows both for AC, so you can compare it with the rating on a transformer or generator, which is often given in VA or kVA.

Worked examples

  • A 10 A heater on 120 V: 10 × 120 = 1,200 W, or 1.2 kW.
  • A 10 A single-phase motor on 230 V with a power factor of 0.85: 10 × 230 × 0.85 = 1,955 W. The apparent power is 10 × 230 = 2,300 VA.
  • A three-phase motor drawing 10 A at 400 V, power factor 0.8: √3 × 10 × 400 × 0.8 = 5,542.56 W, about 5.54 kW. Its apparent power is √3 × 10 × 400 = 6,928.2 VA.
  • A 12 V device drawing 2 A on DC: 2 × 12 = 24 W.

Watts for common currents (power factor 1)

Amps At 120 V At 230 V At 240 V
5 600 1,150 1,200
10 1,200 2,300 2,400
15 1,800 3,450 3,600
20 2,400 4,600 4,800

The effect of the power factor (10 A, 230 V, single phase)

Power factor Watts
1 2,300
0.9 2,070
0.8 1,840
0.7 1,610

Common mistakes

  • Using the DC formula for a motor. Without the power factor you overstate the real power. The product of amps and volts is VA, not watts.
  • Using the voltage to neutral for a three-phase supply. The formula uses the line-to-line voltage. With the voltage to neutral, multiply by 3 instead of √3.
  • Treating a power factor of 1 as typical. It is right for resistive loads only. Use the figure on the rating plate or from the manufacturer.
  • Confusing watts and watt-hours. Watts are power; energy is power multiplied by time. See the energy converter.
  • Treating this as wiring advice. Choosing fuses, breakers and cable depends on rules for your country and installation. Ask a qualified electrician.

To work backwards from watts to amps, use the watts to amps calculator. For power in other units, see the power converter, and to estimate the running cost of a light, the LED savings calculator.

How it is calculated

The current and voltage are multiplied in 40-digit decimal arithmetic. For three phase, the product is multiplied by √3 (1.7320508075688772…). The power factor then multiplies the result for AC. Only the figure displayed is rounded.

Frequently asked questions

How do I convert amps to watts?

Multiply amps by volts. For DC that gives watts directly: 10 A × 120 V = 1,200 W. For AC, multiply by the power factor as well; for three-phase AC multiply by √3 times the line-to-line voltage.

How many watts is 1 amp?

It depends on the voltage. At 120 V one amp is 120 watts, at 230 V it is 230 watts and at 12 V it is 12 watts, in each case for a power factor of 1. An amp alone has no fixed number of watts.

What is the power factor?

The power factor is cos φ, where φ is the phase angle between voltage and current. It runs from 0 to 1 and tells you what fraction of the apparent power (VA) is real power (W). A simple heater or bulb is 1; motors are usually lower.

How do I convert amps to watts for three-phase power?

Multiply √3 (1.732) by the line-to-line voltage, the current in each line, and the power factor. For 10 A at 400 V and a power factor of 0.8 the result is 5,542.56 W.

What is the difference between watts and VA?

Volt-amperes are the product of volts and amps, the apparent power. Watts are the real power, equal to VA multiplied by the power factor. They are equal only when the power factor is 1.

Can I use this to size a breaker or cable?

No. This is arithmetic from the numbers you enter. Breaker and cable sizing depends on local wiring rules and the installation, so ask a qualified electrician.

Related calculators

Sources