Skip to content
thecalculatorstudio

Roofing Calculator: Roof Area, Squares and Shingle Bundles

Enter the plan size and the pitch of each part of the roof, the overhang, and how much waste to allow. You get the true roof area, the squares, and the whole bundles of shingles to order.

Last reviewed

Roof section 1
ft
ft
ft
%

Bundles of shingles

74

24.41 squares with 10% waste

Roof area
2,219 sq ft
Roof area (metric)
206.1 m²
Roofing squares
22.19
Plan area under it
2,048 sq ft

A roofing square is 100 sq ft, and three bundles usually cover one square, but check the label of your shingle. Valleys, hips, ridge and starter courses need their own materials.

What this calculator does

A roof is bigger than the house under it, because a sloping surface is longer than the flat ground it covers. This calculator takes the plan size and the pitch of each part of the roof, adds any overhang, and returns the true roof area, the number of roofing squares, and the bundles of shingles to order, with a waste allowance.

You can add several roof sections, such as a main house and a garage with different pitches. Measure in feet, inches, yards, metres or centimetres, and enter the pitch the way roofers do: the inches the roof rises for every 12 inches of run, so 6 means a 6:12 pitch.

Reading the result

The headline is the number of bundles to buy. Beneath it:

  • Roof area is the true surface area, in square feet and square metres.
  • Roofing squares is the roof area divided by 100.
  • Plan area under it is the footprint, including the overhang.
  • A table shows the pitch, the slope multiplier and the roof area of each section, when you have more than one.

The number of squares and the bundles both include your waste allowance, so the squares in the headline note are the ones you will actually order.

The formulas

If the roof rises r inches for every 12 inches of run, the sloping length is the hypotenuse of a right triangle with sides r and 12. Dividing by the run gives the slope multiplier:

multiplier = √(r² + 12²) ÷ 12

roof area = plan area × multiplier

This holds for any roof whose planes all share the same pitch, however many gables or hips it has. The plan area is the length times the width of the footprint, with the overhang added on every side. Then:

squares = roof area ÷ 100

bundles = squares × (1 + waste ÷ 100) × bundles per square, rounded up

IKO states that three shingle bundles are usually meant to cover a square, and that some makers’ three bundles cover only about 98.4 sq ft, so the calculator lets you set the bundles per square from the label. IKO also says approximately 10 to 15 percent of shingles will be wasted, so the allowance starts at 10%.

Worked examples

A simple house. 64 ft by 32 ft is 2,048 sq ft, or 20.48 squares of plan. At a 5:12 pitch the multiplier is √169 ÷ 12 = 13 ÷ 12 = 1.0833, so the roof is 2,218.7 sq ft, or 22.19 squares. With 10% waste that is 24.41 squares, and at three bundles per square 73.2, so 74 bundles.

With an overhang. A 1 ft overhang all round makes the plan 66 ft by 34 ft, which is 2,244 sq ft. The roof is 2,244 × 13/12 = 2,431 sq ft, or 24.31 squares.

Two sections. A main roof of 30 ft by 20 ft at 6:12 has a roof area of 600 × 1.1180 = 670.8 sq ft. A 12 ft by 12 ft section at 4:12 is 144 × 1.0541 = 151.8 sq ft. Together they are 822.6 sq ft, or 8.23 squares. With 15% waste that is 9.46 squares, and 29 bundles.

A steep roof. 1,000 sq ft of plan at 9:12 is exactly 1,000 × 1.25 = 1,250 sq ft, which is 12.5 squares. With 10% waste, 13.75 squares and 42 bundles.

Reference: slope multipliers

Pitch Slope multiplier Angle
2:12 1.0138 9.5°
3:12 1.0308 14.0°
4:12 1.0541 18.4°
5:12 1.0833 22.6°
6:12 1.1180 26.6°
7:12 1.1577 30.3°
8:12 1.2019 33.7°
9:12 1.2500 36.9°
10:12 1.3017 39.8°
12:12 1.4142 45.0°

A 5:12 pitch is a 5-12-13 right triangle and a 9:12 pitch is a 9-12-15 triangle, so those two multipliers come out as exact fractions: 13/12 and 15/12.

A cross-check with the rafters

For a plain gable roof you can check the area another way. The 32 ft wide house has a run of 16 ft on each side of the ridge. At 5:12 the rafter is 16 × 13/12 = 17.33 ft long. There are two sides, each 64 ft long, so the area is 2 × 17.33 × 64 = 2,218.7 sq ft, the same as the multiplier method. If the two answers differ, check the pitch and the overhang.

A roofing square is 100 square feet, which is 9.29 square metres, so a roof of 22.19 squares is 206 m².

Getting the measurements right

  • Measure the plan, not the slope. Use the length and width of the footprint at ground level or from the plans. The calculator adds the slope.
  • Add the overhang. The eaves and the gable ends extend beyond the walls, and shingles cover them.
  • Measure the pitch. Place a level 12 inches along a rafter or the underside of the roof and measure the rise from the level to the rafter. A smartphone level app gives an angle, which you can convert with the table above.
  • Split complex roofs. Enter each section with its own pitch. Dormers, porches and garages are often at different pitches.
  • Check the label. Bundle coverage differs between products. Use the bundles per square printed on the shingles you will buy.
  • Order the rest separately. Ridge and hip caps, starter strips, underlayment, flashing and nails depend on the roof’s shape and are not in this estimate.

Frequently asked questions

How do I calculate the area of a pitched roof?

Multiply the plan area (the footprint, including any overhang) by the slope multiplier for the pitch. The multiplier is √(rise² + 12²) ÷ 12, where rise is the number of inches the roof climbs for every 12 inches of run. A 32 ft by 64 ft house at 5:12 has 2,048 sq ft of plan and 2,048 × 13/12 = 2,218.7 sq ft of roof.

What is a roofing square?

A roofing square is 100 square feet of roof, the unit roofers use to order and price shingles. A roof of 2,218.7 sq ft is 22.19 squares. IKO notes that three bundles of shingles are usually meant to cover one square.

How many bundles of shingles do I need?

Multiply the squares, including the waste allowance, by the bundles per square and round up. For 22.19 squares with 10% waste, that is 24.41 squares × 3 = 73.2, so 74 bundles. Check the label of your shingle, because bundle coverage varies; IKO says some makers' three bundles cover only about 98.4 sq ft.

How much waste should I allow?

IKO says approximately 10 to 15 percent of the shingles will be wasted, so the calculator starts at 10%. A roof with many hips, valleys and small sections wastes more than a plain gable, so use a figure towards the top of that range for those.

Why is the slope multiplier not the same as the rules of thumb I have seen?

The multiplier here is pure geometry from the Pythagorean theorem, so 5:12 is exactly 13/12, or 1.0833, and 9:12 is exactly 1.25. Some published rules of thumb use rounder or larger factors, which may fold in other allowances. This calculator keeps the geometry and the waste separate so you can see each.

Does this include ridge caps, starter strips and flashing?

No. It calculates the area of shingles for the roof surface. Ridge, hip, starter and valley materials, underlayment, flashing and nails are separate quantities that depend on the roof's shape, so ask your supplier or installer.

Related calculators

Sources