Engine Horsepower Calculator: From Torque and RPM
Enter the torque and the engine speed to get the power, or the power and speed to get the torque. Horsepower and pound-feet are equal at 5,252 rpm.
Last reviewed
Power
285.60 hp
212.97 kW, 289.56 PS
- Horsepower (mechanical)
- 285.599
- Metric horsepower (PS)
- 289.560
- Kilowatts
- 212.971
- Torque
- 300.00 lb·ft, 406.75 N·m
- hp equals lb·ft at
- 5,252.1 rpm
Power is torque times rotation speed. A single torque figure applies at one speed only, since torque changes across the rev range. For the engine's peak power, use the torque and rpm measured together.
Power is torque times speed
An engine’s torque is the twisting force at its crankshaft. Its power is how fast that twisting force can do work, which depends on how fast the shaft is turning. Put the two together and you have the relationship at the heart of this page:
power = torque × rotation speed
An engine that makes a lot of torque at low speed can still make little power, and one that makes modest torque at high speed can make a lot. That is why a diesel truck and a high-revving sports car can both be impressive for different reasons.
The formula
With torque in pound-feet and speed in rpm, power in horsepower is:
horsepower = torque × rpm ÷ 5,252
For an engine making 300 lb·ft at 5,000 rpm:
300 × 5,000 ÷ 5,252.113 = 285.6 hp
In metric, with torque in newton metres, the power in watts is torque × 2π × rpm ÷ 60. For 100 N·m at 6,000 rpm:
100 × 2π × 6,000 ÷ 60 = 62,831.85 W = 62.83 kW, which is 84.26 hp or 85.43 PS.
Where 5,252 comes from
A mechanical horsepower is defined as 550 foot-pounds-force per second, or 33,000 foot-pounds a minute. One revolution turns the shaft through 2π radians. So the power of a torque T at N revolutions a minute is T × 2π × N foot-pounds a minute, and in horsepower:
T × 2π × N ÷ 33,000 = T × N ÷ (33,000 ÷ 2π) = T × N ÷ 5,252.113
The constant is not a rule of thumb, it is an exact consequence of how the horsepower is defined. It also gives a useful fact: at 5,252 rpm, horsepower and pound-feet of torque are equal. On any chart of an engine’s power and torque in those units, the two curves cross at about 5,250 rpm. If they do not, the chart is wrong.
The three units of power
| Unit | Watts | Notes |
|---|---|---|
| Horsepower (hp) | 745.69987 | 550 ft·lbf/s. NIST lists 745.6999 W. |
| Metric horsepower (PS) | 735.49875 | 75 kgf·m/s, exactly. Also written CV or cv. |
| Kilowatt (kW) | 1,000 | The SI unit. |
So 1 hp = 1.01387 PS, and 1 kW = 1.341022 hp. A 200 hp engine is 202.77 PS, or 149.14 kW.
Finding torque from power
The calculation runs the other way. A 200 hp engine at 6,500 rpm has a torque of:
200 × 5,252.113 ÷ 6,500 = 161.6 lb·ft, which is 219.1 N·m.
A 400 hp engine at 7,000 rpm makes 300.12 lb·ft. A peak power figure, in other words, comes with the rpm at which it is reached, and the torque at that point follows.
Crank power and wheel power
Manufacturers usually quote the power at the engine’s crankshaft. What reaches the road is less, because the gearbox, the driveshaft and the differential each take a share. The difference is the drivetrain loss.
The calculator takes the loss as a percentage you enter. With a loss of 15%, an engine making 285.6 hp at the crank puts 242.76 hp at the wheels. How big the loss really is depends on the vehicle, and it is not a fixed figure, so use a figure you have reason to believe in, such as one from a dyno test or from the manufacturer.
Why one torque figure is not enough
Torque varies with engine speed. In many engines the torque rises to a peak at middling revs and falls away toward the limit, while the power can keep rising for longer because it is torque times speed. So:
- The peak power and the peak torque are at different speeds.
- To find the power at a given speed, use the torque at that speed.
- Multiplying a peak-torque figure by the redline speed overstates the power.
If a spec sheet gives “300 lb·ft at 4,000 rpm” and “320 hp at 6,000 rpm”, those are two different points on the curve, and each can be checked against the formula separately.
Common mistakes
- Mixing units. The formula with 5,252 needs pound-feet and rpm. In newton metres the constant is different, which is why the calculator does the conversion.
- Confusing torque with power. They are related by speed, and are not the same thing.
- Comparing hp and PS as if equal. A PS is about 1.4% smaller.
- Treating the figure as what the car delivers. Crank power is higher than wheel power.
- Using inch-pounds. Torque in inch-pounds must be divided by 12 first. The inch-pounds to foot-pounds converter does it.
Related tools
For the running costs of a vehicle, the fuel cost calculator, and for claiming business miles, the mileage calculator. For converting speeds, the speed converter, and for acceleration in g, the acceleration converter.
How it is calculated
The torque is converted to newton metres, with a pound-foot as exactly 1.3558179483314004 N·m. The power in watts is the torque times the angular speed, 2π × rpm ÷ 60. A mechanical horsepower is exactly 550 × 0.3048 × 4.4482216152605 = 745.69987158227 W, and a metric horsepower exactly 75 × 9.80665 = 735.49875 W. Going the other way, the torque is the power divided by the angular speed. All the arithmetic is in 50-digit decimals, rounded only for display.
Frequently asked questions
How do I calculate horsepower from torque and rpm?
Horsepower = torque in pound-feet × rpm ÷ 5,252. An engine making 300 lb·ft at 5,000 rpm produces 285.6 hp. In metric, power in watts is torque in newton metres × 2π × rpm ÷ 60.
Why 5,252?
A horsepower is 33,000 foot-pounds a minute, and one turn of a shaft is 2π radians. 33,000 ÷ 2π is 5,252.113. It is the speed at which the horsepower and pound-feet of torque are the same number.
How many watts is a horsepower?
The mechanical horsepower, 550 foot-pounds-force per second, is 745.69987 watts; NIST lists it as 745.6999 W. The metric horsepower (PS) is exactly 735.49875 W. So 1 hp is 1.01387 PS, and 1 kW is 1.341022 hp.
What is the difference between hp, PS and kW?
They are three units of power. hp is the mechanical horsepower used in the US and UK, PS the metric horsepower used in much of Europe (also written CV or cv), and kW the SI unit. An engine of 200 hp is 202.8 PS or 149.1 kW.
Why is power at the wheels lower?
The gearbox, driveshaft and differential absorb some of the engine's output. Enter a drivetrain loss percentage to see the power at the wheels. With 15% loss, 285.6 hp at the engine is 242.8 hp at the wheels.
Does one torque figure give the engine's power?
Only at that engine speed. Torque changes across the rev range, so the power at 3,000 rpm differs from the power at 6,000. Use the torque and rpm measured at the same point, such as at peak power.
Related calculators
- Fuel Cost CalculatorEnter the distance, how much fuel your car uses and what fuel costs.
- Mileage CalculatorEnter the miles, choose the United States, the United Kingdom or your own rate, and see the amount.
- Speed ConverterConvert any speed.
- Acceleration ConverterConvert any acceleration.
- Inch-Pounds to Foot-Pounds ConverterEnter a torque and convert it.
- Weight CalculatorEnter a mass and choose where it is.
- Tire Size CalculatorType your current tire size and the one you are thinking of.