Skip to content
thecalculatorstudio

Percent Error Calculator: Observed Against Accepted Value

Enter the value you measured and the accepted value. You will see the percent error, whether you were above or below, the absolute and relative error, and the percent difference.

Last reviewed

Percent error

0.1019368%

the observed value is below the accepted value

Signed percent error
-0.1019368%
Absolute error
0.01
Relative error
0.001019368
Percent difference
0.10198878%

Percent error is measured against the accepted value: |observed − accepted| ÷ |accepted| × 100. Percent difference compares two values with neither taken as true, using their mean.

The formula

Percent error says how far a measurement is from the value it should have had, as a percentage of that value.

Percent error = |observed − accepted| ÷ |accepted| × 100

The observed (or experimental, or measured) value is what you got. The accepted (or true, or theoretical) value is what a reference says it should be. The bars mean absolute value, so the answer is never negative. The accepted value goes underneath because the error is judged against what is correct.

In MathWorld’s terms, percentage error is 100% times the relative error, and relative error is the absolute error divided by the true value.

Worked examples

1. Measuring gravity. You measure the acceleration due to gravity as 9.8 m/s² and the accepted value is 9.81 m/s².

  • Absolute error: |9.8 − 9.81| = 0.01
  • Divide by the accepted value: 0.01 ÷ 9.81 = 0.0010194
  • Times 100: 0.1019%

The observed value is below the accepted one, so the signed percent error is −0.1019%.

2. A reading that is too high. You read 105 where the true value is 100.

  • Absolute error: 5
  • 5 ÷ 100 × 100 = 5% (signed +5%)

3. Too low by the same amount. You read 95 against 100: the percent error is again 5%, and the signed figure is −5%.

4. A negative accepted value. A reading of −45 where the accepted value is −50 is out by 5, and 5 ÷ 50 × 100 = 10%. The page divides by the size of the accepted value, so a positive signed figure always means the observed value is higher than the accepted one.

5. A large error. An observed value of 2 against an accepted value of 0.5 is out by 1.5, which is 300% of 0.5. A percent error can exceed 100%.

Signed or absolute

The textbook figure is the absolute one, which is why it is never negative. The signed version keeps the direction. In a lab report the sign is worth a comment: a negative signed error means your measurement was consistently low, which may point to a cause such as heat loss or a stopwatch started late.

Percent error and percent difference

They are not the same, and mixing them up is a common mistake.

  • Percent error compares a measurement with a value taken as true. The base is the accepted value.
  • Percent difference compares two values when neither is the reference, such as two students’ results. The base is their mean: |a − b| ÷ ((|a| + |b|) ÷ 2) × 100.

For 105 and 100 the percent error against 100 is 5%, while the percent difference is 5 ÷ 102.5 × 100 = 4.878%. This page shows both, and labels them.

Observed Accepted Percent error Percent difference
9.8 9.81 0.1019% 0.1020%
105 100 5% 4.878%
95 100 5% 5.128%
1.5 1.2 25% 22.22%
2 0.5 300% 120%

Error, accuracy and precision

Percent error measures accuracy: how close you are to the true value. It says nothing about precision, how closely repeated measurements agree. A set of readings can be tightly grouped and still all wrong (precise but not accurate), or scattered around the right value (accurate on average but imprecise). To describe the spread of repeated measurements, use the statistics calculator, which gives the mean and standard deviation.

When the accepted value is zero

Percent error divides by the accepted value, so it cannot be worked out if that value is zero. The page says so and does not guess. For quantities that should be zero, such as a balance reading with nothing on the pan, report the absolute error in the units measured.

Common mistakes

  • Dividing by the observed value. The accepted value goes on the bottom. Using the measured one gives a different number.
  • Forgetting to multiply by 100. 0.05 is the relative error. 5% is the percent error.
  • Mixing up percent error and percent difference. Use percent error when one value is the reference.
  • Rounding too early. Keep the full difference through the sum and round the final percentage.
  • Calling a percent error “percentage points”. A 5% error is not 5 percentage points.

How it is calculated

Observed and accepted values are read as exact decimals. The difference is observed minus accepted. The relative error is the absolute difference divided by the absolute accepted value, and the percent error is that times 100. The signed percent error is the signed difference divided by the absolute accepted value, times 100. Percent difference divides the absolute difference by the mean of the two absolute values. Everything is worked to 40 digits and shown to 12 significant digits.

Frequently asked questions

What is the percent error formula?

Percent error = |observed − accepted| ÷ |accepted| × 100. If you measure 9.8 and the accepted value is 9.81, the difference is 0.01, and 0.01 ÷ 9.81 × 100 is 0.1019%.

Which value goes on the bottom?

The accepted (true) value. The error is measured against what the answer should have been, not against what you measured, so swapping them gives a different percentage.

Can percent error be negative?

The usual figure is not, because it uses the absolute difference. The signed version is negative when the measured value is lower than the accepted one, which tells you which way you were out.

What is the difference between percent error and percent difference?

Percent error compares a measurement with a value taken as true. Percent difference compares two values neither of which is true, using their mean as the base. 105 against 100 is 5% error but 4.88% difference.

What if the accepted value is zero?

Percent error is undefined, because it divides by the accepted value. Report the absolute error instead, in the units you measured.

How much percent error is acceptable?

It depends on the experiment and the instrument. There is no universal limit. Your teacher, lab manual or standard sets one, and the page only works out the figure.

Related calculators

Sources